Product Details
Configured for high-speed industrial network interfacing within IRC5 controller platforms, the ABB DSQC 658 (3HAC037084-001 DeviceNet Board) provides direct physical signal transmission and data communication protocol execution.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | DSQC 658 |
| Brand | ABB |
| Part Number | 3HAC037084-001 |
| Origin | Canada |
| Weight | 0.04 kg |
| Dimensions | 140 mm x 130 mm x 10 mm |
| Operating Temp | Standard industrial ambient |
| Power Consumption | System backplane dependent |
| Software Requirement | RW 5.13 or higher |
| Interface Type | DeviceNet |
Profinet / EtherNet/IP deterministic networks
The DSQC 658 facilitates deterministic data exchange within the IRC5 architecture, ensuring low-latency communication between the controller and DeviceNet field devices. The hardware integration requires RobotWare 5.13 or later to ensure proper firmware flash compatibility and register mapping. Field bus synchronization is handled through the dedicated backplane bus communication velocity architecture, which minimizes jitter in cyclic data transfers. Users must verify that the master configuration file matches the slave device node address and baud rate settings to maintain network integrity and prevent bus-off states.
Frequently Asked Questions
Q: Is this board compatible with RobotWare versions earlier than 5.13?
A: No, firmware architecture within the DSQC 658 requires a minimum of RobotWare 5.13 to initiate the communication stack and hardware handshake successfully.
Q: Does the board support hot-swapping during active controller operation?
A: No. Any hardware modification or insertion must be performed while the control system is powered down to prevent damage to the backplane connectors and signal logic.
Field Installation Guidelines
- Static Precautions: Always wear an ESD-compliant wrist strap connected to a common ground point when handling the PCB to prevent discharge damage to sensitive IC components.
- Physical Mounting: Ensure the board is seated firmly within the designated controller slot. Tighten the retaining screws to the specified torque to guarantee a stable electrical connection to the backplane bus.
- Shielding and Grounding: DeviceNet cables must utilize twisted-pair cabling with adequate shielding. Ensure the shield is grounded at a single point, ideally at the power supply or the designated cabinet grounding lug, to prevent ground loops.
- Termination: Install a 121 ohm 0.25 W resistor at both ends of the DeviceNet trunk line to suppress signal reflections and maintain characteristic impedance.
- Wiring: Maintain physical separation between DeviceNet communication lines and high-voltage power cables to mitigate electromagnetic interference (EMI).
Additional Information
- 100% Genuine Parts: All products are original and authentic, ensuring reliable industrial performance.
- 30-Day Refund Guarantee: Return any in-stock item within 30 days in original, unopened packaging for a full refund (excluding shipping and fees).
- 12-Month Warranty: Covers defects in materials or workmanship; excludes misuse, normal wear, or unauthorized modifications.
- Worldwide Shipping: We ship via USPS, UPS, FedEx, and DHL. Delivery times vary by country and may be subject to customs or import fees.
- Support & Contact: Technical and warranty assistance is available anytime. Contact us here: Contact.
- Purchase Guidance: Check product specifications and compatibility carefully before ordering to ensure proper application.
Tech & Buying Guide
FAT vs SAT in Industrial Control Systems: Key Differences and Execution Guide
Industrial control system deployment relies on strict verification protocols to guarantee operational safety, system stability, and regulatory compliance. Commissioning complex Programmable Logic Controller (PLC) racks, Distributed Control Systems (DCS), and Safety Instrumented Systems (SIS) requires two critical milestones: the Factory Acceptance Test (FAT) and the Site Acceptance Test (SAT). Both procedures validate that system automation meets design specifications, but they occur at different stages of project execution and target distinct operational risks.
Hub vs Switch vs Router in Industrial Automation Architecture
Modern factory automation relies on reliable industrial networking infrastructure to exchange real-time field data across operational technology systems. Engineers often encounter networking hardware like hubs, switches, and routers when integrating Programmable Logic Controllers, Distributed Control Systems, and SCADA monitoring nodes. Although these devices share physical ports, they operate at different layers of the Open Systems Interconnection reference model and deliver distinct traffic management capabilities.
Marshalling Cabinet Preventive Maintenance: Essential Healthiness Checks for PLC, DCS, and ESD Systems
Marshalling cabinets serve as the vital interface between field instrumentation and control room electronics in modern process facilities. Regular preventive maintenance of these cabinets ensures signal integrity across programmable logic controllers (PLCs), distributed control systems (DCS), and emergency shutdown (ESD) networks. System technicians must execute structured inspection protocols to mitigate environmental risks, identify loose wiring, and maintain continuous operational readiness.