{"product_id":"woodward-5464-550-discrete-output-module","title":"Woodward 5464-550 Discrete Output Module","description":"\u003cp\u003eConfigured for digital control signal execution in NETCON 5000 turbine management platforms, the \u003cstrong\u003eWoodward 5464-550\u003c\/strong\u003e (\u003cstrong\u003e5464-550\u003c\/strong\u003e Discrete Output Module) provides direct physical execution of binary command signals and system fault status monitoring.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e5464-550\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eWoodward\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e2.05 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface\u003c\/td\u003e\n\u003ctd\u003eSingle port\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIndicators\u003c\/td\u003e\n\u003ctd\u003eRed fault LED\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eActuator Loop Feedback Response and Thermal Heat Sink Dissipation Profiles\u003c\/h3\u003e\n\u003cp\u003eThe 5464-550 module manages the switching of discrete control signals required for binary actuation and machine logic state changes. The module internal architecture is designed with specific thermal heat sink dissipation profiles to maintain component reliability under continuous switching load. To support stable actuator loop feedback response, the module maintains low-impedance switching paths, minimizing latency between the control processor output and the field-side load. The integrated red fault indicator monitors internal module health, providing immediate visual feedback if the processor detects a hardware anomaly or a discrepancy in output state compared to the logic command.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the module support hot-swapping within an active NETCON 5000 rack?\u003c\/p\u003e\n\u003cp\u003eA: Hot-swapping the 5464-550 is not supported. The control rack power must be removed prior to module extraction or insertion to prevent damage to the backplane communication pins or inadvertent state changes in the controlled field equipment.\u003c\/p\u003e\n\u003cp\u003eQ: How is the fault indicator state synchronized with the system logic?\u003c\/p\u003e\n\u003cp\u003eA: The fault LED is driven by the module's internal diagnostic logic upon detection of a communication fault with the central processor or an internal hardware failure. The state is not user-configurable and acts strictly as a hardware status indicator.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Secure the module firmly into the designated slot on the NETCON 5000 rack. Ensure the locking tabs are fully engaged to guarantee consistent backplane bus contact.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring:\u003c\/strong\u003e Connect field output devices to the module terminals using shielded conductors. Ensure that the total current draw for each discrete output does not exceed the maximum rating for the module terminal pins.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding:\u003c\/strong\u003e Verify the module chassis is properly bonded to the cabinet ground reference. This connection is required to provide a stable return path for noise currents and to maintain the integrity of the output switching circuit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTesting:\u003c\/strong\u003e Perform a controlled logic test post-installation to confirm that the discrete output states correctly correlate with the turbine control command signals. Observe the fault LED during power-up to confirm successful self-initialization.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Woodward","offers":[{"title":"Default Title","offer_id":53005498286389,"sku":"5464-458","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/5463-7832_e5afef1f-5587-4173-b263-947c0bfe6fc4.png?v=1781602950","url":"https:\/\/www.5gplc.com\/products\/woodward-5464-550-discrete-output-module","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}