{"product_id":"pr6423-010-030-con021-emerson-eddy-current-sensors","title":"PR6423\/010-030 \u0026 CON021 | Emerson | Eddy Current Sensors","description":"\u003cp\u003eConfigured for non-contact displacement monitoring in rotating machinery, the \u003cstrong\u003eEmerson PR6423\/010-030\u003c\/strong\u003e (\u003cstrong\u003ePR6423\/010-030\u003c\/strong\u003e) transducer paired with the \u003cstrong\u003eCON021\u003c\/strong\u003e signal converter provides direct physical\/electrical execution.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003ePR6423\/010-030 + CON021\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eEmerson\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUnited States\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.3 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e4.1 cm x 15.9 cm x 10.8 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eIndustrial grade\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eNominal excitation required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eGap Voltage Validation (-10 VDC targets)\u003c\/h3\u003e\n\u003cp\u003eThe system utilizes an oscillator circuit to drive the transducer probe, creating an electromagnetic field for displacement detection. To ensure accurate linearization, the system necessitates precise gap voltage validation during commissioning. The converter centers its output characteristic around a nominal target of -10 VDC, representing the mid-point of the physical measurement gap. Maintenance of this -10 VDC baseline is mandatory for accurate signal tracking; significant deviations indicate mechanical misalignment, transducer saturation, or degradation of the conductive target surface.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the CON021 converter support hot-swap replacement?\u003c\/p\u003e\n\u003cp\u003eA: The converter is designed for rack-based mounting systems. Hot-swap capability depends on the backplane architecture of the monitoring rack. Ensure the specific rack chassis supports energized module removal before attempting replacement.\u003c\/p\u003e\n\u003cp\u003eQ: Is shielding required for the probe cable?\u003c\/p\u003e\n\u003cp\u003eA: Yes. To mitigate electromagnetic interference, the probe cable must be routed through grounded metallic conduit, and the shield must be terminated exclusively at the monitoring system rack to prevent ground-loop current injection.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eMount the transducer in a rigid, vibration-isolated bracket to minimize extraneous mechanical noise and prevent housing fatigue.\u003c\/li\u003e\n\u003cli\u003eEnsure the measurement target surface is clean and free of non-conductive coatings to maintain the required electrical conductivity.\u003c\/li\u003e\n\u003cli\u003eEstablish the nominal air gap using a non-metallic feeler gauge to prevent contact damage to the sensor tip during startup.\u003c\/li\u003e\n\u003cli\u003eRoute signal cabling through grounded metallic conduit, keeping lines physically separated from high-current AC power lines.\u003c\/li\u003e\n\u003cli\u003eTerminate the signal shield at the monitoring system (DCS\/TSI) rack only.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"EMERSON","offers":[{"title":"Default Title","offer_id":53009136484661,"sku":"CON021+PR6423\/010-030","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/CON021_PR6423003-130_bc1e35a6-a1f5-4583-99c5-ad8994ad7a65.png?v=1781685798","url":"https:\/\/www.5gplc.com\/products\/pr6423-010-030-con021-emerson-eddy-current-sensors","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}