{"product_id":"is420eswbh5a-general-electric-ethernet-ionet-switch","title":"IS420ESWBH5A | General Electric | Ethernet IONet Switch","description":"\u003cp\u003eConfigured for deterministic industrial networking in Mark VIeS systems, the \u003cstrong\u003eGE IS420ESWBH5A\u003c\/strong\u003e (\u003cstrong\u003eIS420ESWBH5A\u003c\/strong\u003e Ethernet Switch) provides direct physical\/electrical execution.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS420ESWBH5A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eNot Specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e18.8 cm x 8.6 cm x 5.6 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-40 deg C to +70 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e24\/28 VDC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNetwork Ports\u003c\/td\u003e\n\u003ctd\u003e8 x 10\/100Base-TX (RJ-45), 2 x 100Base-LX10 (Fiber)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control and Drives Characteristics\u003c\/h3\u003e\n\u003cp\u003eThe IS420ESWBH5A is optimized for Profinet\/EtherNet\/IP deterministic networks, maintaining packet delivery timing required for Mark VIeS control synchronization. The switch architecture supports high-velocity backplane bus communication, ensuring that multicast traffic is handled without inducing jitter in I\/O scanning cycles. Firmware flash compatibility allows for network performance updates, while the non-interfering safety rating ensures that the switch does not compromise the operational integrity of the connected control hardware.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does this switch support hot-swapping during active system operation?\u003c\/p\u003e\n\u003cp\u003eA: No. While the switch provides network connectivity, removing the unit from the backplane or disconnecting the Phoenix Contact power supply will interrupt network communication to all devices connected through it, resulting in a loss of I\/O link for the associated controllers.\u003c\/p\u003e\n\u003cp\u003eQ: Are the fiber ports compatible with standard single-mode and multi-mode infrastructure?\u003c\/p\u003e\n\u003cp\u003eA: The fiber ports are 100Base-LX10. Ensure the installed cable media matches the LX10 specification to avoid signal attenuation or link negotiation failures.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Utilize the provided 259B2451BVP4 mounting clip for perpendicular orientation on a DIN rail. Ensure the device is mounted to allow vertical convection cooling, as the unit relies on ambient air circulation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable Termination:\u003c\/strong\u003e For copper ports, use Cat 5e UTP cabling with RJ-45 connectors. Ensure cable runs do not exceed 100 meters and are routed in separate trays from high-voltage AC lines to prevent induced signal errors.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding:\u003c\/strong\u003e Secure the device housing to a chassis ground point to ensure compliance with hazardous location (Class 1, Div 2) grounding requirements and to mitigate potential electromagnetic interference.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower Connection:\u003c\/strong\u003e Verify the 24\/28 VDC supply polarity at the Phoenix Contact connector before application. Improper polarity may damage internal protection circuitry.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52988563292469,"sku":"IS420ESWBH5A","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/IS420ESWBH5A.png?v=1781157276","url":"https:\/\/www.5gplc.com\/products\/is420eswbh5a-general-electric-ethernet-ionet-switch","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}