{"product_id":"honeywell-05704-a-0145-four-channel-control-card","title":"Honeywell 05704-A-0145 Four Channel Control Card","description":"\u003cp\u003eThe \u003cstrong\u003eHoneywell 05704-A-0145\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003e05704-A-0145\u003c\/strong\u003e Four Channel Control Card, operates as a dedicated hardware component for multi-channel gas detector signal acquisition and alarm management within distributed control system platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e05704-A-0145\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eHoneywell\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eNot Specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.17 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e132 x 25 x 172 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eNot Specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e7.5 W (Typical) \/ 8.3 W (Maximum)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eChannel Count\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSignal Range\u003c\/td\u003e\n\u003ctd\u003e0 to 25 mA (Linear)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLoop Supply\u003c\/td\u003e\n\u003ctd\u003eIsolated 24 V ± 5% (25 mA max)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eDCS Process Control and Connectivity\u003c\/h3\u003e\n\u003cp\u003eThe 05704-A-0145 facilitates high-precision signal processing for gas detection loops through an isolated 24 VDC supply architecture. To maintain measurement integrity, the card provides channel-to-channel isolation and comprehensive loop protection against short circuits up to ±50 V. The design supports linear current input ranges up to 25 mA, ensuring compatibility with standard 4-20 mA HART loop protocol instruments. Cold junction compensation (CJC) is not required for these current-loop inputs; however, the module's internal circuitry performs active filtering to mitigate common-mode noise, ensuring that alarm facilities are triggered only by valid gas concentration variations.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does this control card support hot-swapping within the card rack?\u003c\/p\u003e\n\u003cp\u003eA: Hot-swapping is not recommended unless supported by the specific rack backplane power distribution system. Removing or inserting the card under power may trigger transient current spikes that could potentially cause an unintended alarm state or damage to the input current sense resistors.\u003c\/p\u003e\n\u003cp\u003eQ: What are the limitations regarding field wiring resistance?\u003c\/p\u003e\n\u003cp\u003eA: The maximum allowed line resistance for the sensor loop, including the sensor itself, is 500 ohms. Exceeding this limit will result in voltage drops that prevent the card from supplying the necessary 24 V loop power, leading to measurement inaccuracies or sensor communication failure.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eEnsure the control card rack is de-energized before inserting the 05704-A-0145 into the designated slot.\u003c\/li\u003e\n\u003cli\u003eVerify that all field wiring is terminated at the rack terminal block; ensure the cable shield is connected to the chassis ground to minimize electromagnetic interference (EMI).\u003c\/li\u003e\n\u003cli\u003eConfirm that the sensor is configured as a current source, as this card expects current-based input signals.\u003c\/li\u003e\n\u003cli\u003eAfter insertion, secure the card faceplate screws to ensure proper grounding and mechanical alignment within the rack.\u003c\/li\u003e\n\u003cli\u003ePerform a functional verification by injecting a simulated 4-20 mA signal at the field termination point and confirming the display and alarm response on the control system interface.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Honeywell","offers":[{"title":"Default Title","offer_id":52975917662517,"sku":"05704-A-0145","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/05704-A-0145.png?v=1780988539","url":"https:\/\/www.5gplc.com\/products\/honeywell-05704-a-0145-four-channel-control-card","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}