{"product_id":"general-electric-is410jpddg1a-dc-power-distribution-card","title":"General Electric IS410JPDDG1A DC Power Distribution Card","description":"\u003cp\u003eConfigured for power supply management in Mark VIe control platforms, the \u003cstrong\u003eGE IS410JPDDG1A\u003c\/strong\u003e (\u003cstrong\u003eIS410JPDDG1A\u003c\/strong\u003e) DC Power Distribution Card provides direct physical\/electrical execution.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS410JPDDG1A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e16.51 cm x 17.8 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-30 deg C to +65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive (Distribution hub)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDistribution Types\u003c\/td\u003e\n\u003ctd\u003e28 VDC (Control), 48 VDC\/24 VDC (Wetting)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control and Drives Characteristics\u003c\/h3\u003e\n\u003cp\u003eThe IS410JPDDG1A acts as the primary power distribution hub within the Mark VIe architecture, managing multiple DC voltage domains. It features circuitry to monitor two channels of AC distribution and supports a floating DC wetting power bus, which is referenced to earth through dedicated resistor networks. Voltage feedback is transmitted via the PPDA interface, allowing the control system to detect and isolate ground faults autonomously. Deterministic power delivery is maintained by the board's structural design, which ensures compatibility with existing backplane bus communication velocity and I\/O module power requirements.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the JPDG card support hot-swapping while the system is powered?\u003c\/p\u003e\n\u003cp\u003eA: No. The JPDG serves as a critical distribution node for multiple power rails. Removing or installing the card while under load will interrupt power to downstream control components and I\/O modules, likely causing a system trip. Always de-energize the power input feeds before board replacement.\u003c\/p\u003e\n\u003cp\u003eQ: How is the floating DC wetting power bus managed to prevent ground faults?\u003c\/p\u003e\n\u003cp\u003eA: The bus is centered on earth via resistive networks. This configuration allows the monitoring circuitry to measure potential shifts between the bus and ground, which are then reported via the PPDA to identify and locate fault conditions.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Secure the board onto the DIN rail using the integrated mounting clips. Ensure the DIN rail is properly grounded to the cabinet frame to support the board’s ground reference requirements.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring:\u003c\/strong\u003e Terminate power input and distribution cabling using appropriately rated lugs. Ensure that the wire gauge is sufficient for the total current draw of the distributed circuits to prevent localized overheating.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding:\u003c\/strong\u003e Verify the resistance of the earth-referencing resistors during commissioning to ensure the floating bus is correctly referenced to the system ground.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable Separation:\u003c\/strong\u003e Keep power distribution cabling physically separated from signal-level wiring to minimize electromagnetic interference and ensure the stability of the voltage feedback signals reported to the PPDA.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52988256813365,"sku":"IS410JPDDG1A","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/IS410JPDDG1A.png?v=1781156953","url":"https:\/\/www.5gplc.com\/products\/general-electric-is410jpddg1a-dc-power-distribution-card","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}