{"product_id":"general-electric-ds200tbcbg1aaa-4-20-ma-rtd-input-termination-module","title":"General Electric DS200TBCBG1AAA 4-20 mA RTD Input Termination Module","description":"\u003cp\u003eConfigured for signal interface within Mark V Speedtronic systems, the \u003cstrong\u003eGE DS200TBCBG1AAA\u003c\/strong\u003e (\u003cstrong\u003eDS200TBCB\u003c\/strong\u003e Input Termination Module) provides direct physical execution for RTD and current loop sensor landing.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200TBCBG1AAA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e+5 V DC, 6 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCore Function\u003c\/td\u003e\n\u003ctd\u003eRTD and 4-20 mA signal termination\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control \u0026amp; Firmware Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe DS200TBCBG1AAA operates as a passive interface board, facilitating I\/O density scaling by routing temperature and process current signals to the TCCB board within the core. Deterministic signal transmission is achieved through a fixed hardware architecture; the module does not require firmware, thereby avoiding firmware flash compatibility requirements. Eight of the input channels support hardware-level reconfiguration via jumpers to switch from 4-20 mA to 0-1 mA signal ranges. Signal integrity is maintained through integrated termination logic that interfaces directly with the backplane bus, ensuring that converted sensor data is correctly mapped to the system's control processors.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the input range be modified for specific channels?\u003c\/p\u003e\n\u003cp\u003eA: Yes. Eight of the 4-20 mA input channels feature hardware jumpers that allow for reconfiguration to support 0-1 mA input signals. This physical adjustment must be made at the board level.\u003c\/p\u003e\n\u003cp\u003eQ: Is this module hot-swappable during system operation?\u003c\/p\u003e\n\u003cp\u003eA: No. The TBCB module must be de-energized before removal or installation. Ensure that all power is removed from the associated core and terminal blocks to prevent damage to the module circuitry or accidental disruption of the control loops.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSignal Routing\u003c\/strong\u003e: Ensure all RTD and mA sensor leads are landed securely on the terminal blocks. Verify signal polarity for 4-20 mA loops to prevent open-circuit or reversed-polarity conditions.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJumper Configuration\u003c\/strong\u003e: If using the 0-1 mA input range, verify that the corresponding jumpers are correctly set before energizing the module. Improper jumper settings may lead to signal reading errors at the controller level.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding and Shielding\u003c\/strong\u003e: Terminate sensor cable shields at the designated chassis ground points. Maintaining a low-impedance ground reference is necessary to minimize common-mode noise on the sensitive RTD temperature measurement circuits.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCabinet Integration\u003c\/strong\u003e: Mount the module in location seven of the core assembly. Ensure proper alignment with the backplane connector to avoid pin deformation during insertion.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52991847891253,"sku":"DS200TBCBG1AAA","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/DS200TBCBG1AAA.png?v=1781250897","url":"https:\/\/www.5gplc.com\/products\/general-electric-ds200tbcbg1aaa-4-20-ma-rtd-input-termination-module","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}