{"product_id":"general-electric-ds200slccg3a-lan-communication-card","title":"General Electric DS200SLCCG3A LAN Communication Card","description":"\u003cp\u003eConfigured for high-speed network integration within Mark V and EX2000 control platforms, the \u003cstrong\u003eGE DS200SLCCG3A\u003c\/strong\u003e (\u003cstrong\u003eDS200SLCC\u003c\/strong\u003e LAN Communication Card) provides direct physical\/electrical execution of LAN-based controller communication.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200SLCCG3A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eStandard Mark V PCB footprint\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003ePer Mark V environmental standards\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eBackplane rail supply\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProcessor\u003c\/td\u003e\n\u003ctd\u003eLAN Control Processor (U1)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface\u003c\/td\u003e\n\u003ctd\u003e16-position alphanumeric display\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control and Firmware Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eDS200SLCCG3A\u003c\/strong\u003e facilitates deterministic data exchange across the Mark V backplane. Proper operation is contingent upon backplane bus communication velocity settings that synchronize the LAN control processor with the driver controller processor (DCP) on the SDCC board. Firmware flash compatibility is managed via replaceable EPROMS (U6, U7), which house the LCP software stack. Any replacement of these memory modules requires strict adherence to checksum validation to ensure data integrity during LCP execution. I\/O density scaling is supported through the board's dual-ported RAM (U5) architecture, which regulates the data handshaking between the LAN controller and host drive electronics.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: How is the LCP software updated on the SLCC board?\u003c\/p\u003e\n\u003cp\u003eA: The LCP software is stored in replaceable EPROMS located at U6 and U7. To update, remove the board, extract the existing EPROMS, and install the new programmed EPROMS into the designated sockets while observing static discharge precautions.\u003c\/p\u003e\n\u003cp\u003eQ: What is the purpose of the connector labeled KPPL?\u003c\/p\u003e\n\u003cp\u003eA: The KPPL connector serves as the interface for the programmer module. This module allows operators to perform diagnostic testing, adjust software parameters, and view fault codes via the 16-position alphanumeric display.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eStatic Sensitivity\u003c\/strong\u003e: The SLCC board utilizes sensitive CMOS components. Always wear a grounded anti-static wrist strap when handling the PCB to prevent permanent damage to the LCP or memory modules.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Alignment\u003c\/strong\u003e: Ensure all system-level connections to the NTB\/3TB, SDCC, and TCCB boards via the 2PL connector are fully seated. Improper seating of the 2PL or 3PL connectors can cause communication timeouts between the LCP and the SDCC.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProgrammer Module\u003c\/strong\u003e: When mounting the programmer module onto the KPPL connector, apply uniform pressure to ensure the pins are correctly aligned and fully engaged to prevent intermittent diagnostic data.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComponent Verification\u003c\/strong\u003e: Before energizing the cabinet, verify that EPROMS U6 and U7 are oriented correctly according to the notch index on the socket. Reverse installation will result in immediate boot-up failure.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding\u003c\/strong\u003e: Ensure the board is properly secured to the cabinet chassis via its mounting screws to maintain the integrity of the isolated and non-isolated circuit grounding paths.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":53039280652597,"sku":"DS200SLCCG3A","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/DS200SLCCG3AFG_fcf98d68-c3db-4021-b14a-3c1c61d8c2dc.png?v=1782464988","url":"https:\/\/www.5gplc.com\/products\/general-electric-ds200slccg3a-lan-communication-card","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}