{"product_id":"general-electric-ds200slccg1acc-lan-communication-module","title":"General Electric DS200SLCCG1ACC LAN Communication Module","description":"\u003cp\u003eConfigured for network interfacing within Mark V drive and turbine control platforms, the \u003cstrong\u003eGE DS200SLCCG1ACC\u003c\/strong\u003e (\u003cstrong\u003eDS200SLCCG1\u003c\/strong\u003e LAN Communication Card) provides direct physical data exchange and local control processing.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200SLCCG1ACC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCore Function\u003c\/td\u003e\n\u003ctd\u003eLAN communication and processor interfacing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control \u0026amp; Firmware Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe DS200SLCCG1ACC integrates a LAN Control Processor (LCP) and utilizes dual-ported RAM to facilitate deterministic data exchange with the host drive control board. For consistent system operation, the backplane bus communication velocity must remain synchronized with the LCP processing cycle to prevent data bottlenecks. Firmware-related parameters are managed via the two onboard EPROM memory modules; these components must maintain version parity with the host controller firmware to ensure correct I\/O density scaling and operational stability. The module supports both isolated and non-isolated communication channels, requiring strict adherence to hardware configuration standards to prevent electrical noise coupling from the network medium into the control bus.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: How is the module interfaced with the host drive controller?\u003c\/p\u003e\n\u003cp\u003eA: The board utilizes dual-ported RAM to create a shared memory buffer between the LCP and the drive control board. This allows for simultaneous, independent access by both microprocessors for high-speed data transfer without external polling.\u003c\/p\u003e\n\u003cp\u003eQ: What is the utility of the attachable alphanumeric keypad?\u003c\/p\u003e\n\u003cp\u003eA: The 16-position alphanumeric display provides a physical interface for users to access system control settings and perform local diagnostics directly on the communication module, facilitating rapid status assessment.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhysical Seating\u003c\/strong\u003e: Ensure the card is inserted into the designated drive cabinet slot. Verify that all backplane connectors are fully engaged to prevent intermittent communication failures, which can trigger system-wide control faults.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShielding and Grounding\u003c\/strong\u003e: The module incorporates both isolated and non-isolated circuitry. Ensure that external network cabling is properly shielded and that the cabinet ground is securely bonded. Failure to isolate the signal path correctly can result in ground loops affecting data integrity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMemory Handling\u003c\/strong\u003e: When replacing or servicing the EPROM memory modules, utilize ESD-safe handling procedures. Ensure proper orientation during installation to prevent damage to the U1 LCP and its peripheral support logic.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagnostic Verification\u003c\/strong\u003e: Following installation, attach the 16-position keypad to the designated port to verify initialization. Monitor for error codes or status messages that indicate successful handshaking between the card and the host drive controller.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52991670026549,"sku":"DS200SLCCG1ACC","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/DS200SLCCG1ACC.png?v=1781246590","url":"https:\/\/www.5gplc.com\/products\/general-electric-ds200slccg1acc-lan-communication-module","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}