{"product_id":"ge-is415ucvgh1a-vme-controller-card","title":"GE IS415UCVGH1A VME Controller Card","description":"\u003cp\u003eConfigured for real-time turbine regulation in Mark VI platforms, the \u003cstrong\u003eGE IS415UCVGH1A\u003c\/strong\u003e (\u003cstrong\u003eIS415UCVGH1A\u003c\/strong\u003e VME Controller Card) provides direct physical\/electrical execution of logic processing and network communication.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS415UCVGH1A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eSingle-slot VME\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 deg C to 70 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e+5 V DC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMicroprocessor\u003c\/td\u003e\n\u003ctd\u003eIntel Ultra Low Voltage Celeron 650 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMemory\u003c\/td\u003e\n\u003ctd\u003e128 MB SDRAM \/ 128 MB Flash\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS415UCVGH1A utilizes dual 10BaseT\/100BaseTX Ethernet ports to maintain deterministic communication across the Mark VI rack architecture. The primary port facilitates UDH configuration and peer-to-peer data exchange, while the secondary port enables dedicated EGD networks or Modbus protocols on isolated logical subnets. Firmware flash compatibility is verified at each power cycle, where the controller cross-references the internal toolbox configuration against the detected hardware backplane bus communication velocity and physical I\/O density to ensure system-wide synchronicity.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is the IS415UCVGH1A compatible with live firmware updates?\u003c\/p\u003e\n\u003cp\u003eA: Firmware updates require a controlled power cycle of the VME rack. The controller performs a hardware-software match verification upon reboot; unauthorized firmware modifications will inhibit the controller from transitioning to an \"Execute\" state.\u003c\/p\u003e\n\u003cp\u003eQ: Does the controller support hot-swapping within the VME rack?\u003c\/p\u003e\n\u003cp\u003eA: No. Due to the reliance on backplane bus synchronization and volatile state registers, the IS415UCVGH1A must not be removed or inserted while the rack is energized. Improper removal will disrupt the deterministic network and may trigger a system-wide trip.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eVME Slot Alignment\u003c\/strong\u003e: Ensure the card is inserted into the correct designated slot for the master controller. Verify the edge connector pins are free of oxidation to prevent high-resistance contact that could impede backplane communication velocity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding\u003c\/strong\u003e: The VME chassis must be connected to a common earth ground. Secure the front-panel captive screws to ensure the module's conductive faceplate is bonded to the rack chassis, providing an effective shield against electromagnetic interference.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEthernet Cabling\u003c\/strong\u003e: Utilize shielded Category 5e (or higher) Ethernet cables for all network connections. Ensure the cable bend radius does not exceed the manufacturer’s specification to maintain the integrity of the 100BaseTX data signals.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eToolbox Configuration\u003c\/strong\u003e: After physical installation, use the GE Toolbox application to verify the network IP configuration. The controller will log a mismatch error if the detected physical hardware does not match the parameters stored in the configuration project.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52949133689141,"sku":"IS415UCVGH1A","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/IS415UCVGH1A.png?v=1780301354","url":"https:\/\/www.5gplc.com\/products\/ge-is415ucvgh1a-vme-controller-card","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}