{"product_id":"ge-is210macch2a-printed-circuit-board","title":"GE IS210MACCH2A Printed Circuit Board","description":"\u003cp\u003eConfigured for input and output signal processing in Mark VI control architectures, the \u003cstrong\u003eGE IS210MACCH2A\u003c\/strong\u003e (\u003cstrong\u003eIS210MACCH2A\u003c\/strong\u003e I\/O Board) provides direct physical and electrical execution of terminal-level data routing.\u003c\/p\u003e\n\u003ch3\u003eSuffix Breakdown \u0026amp; Model Matrix\u003c\/h3\u003e\n\u003cp\u003eThe IS210MACCH2A is a singular hardware revision of the Mark VI I\/O board series. No modular decomposition is required for operation, as this unit functions as a fixed-configuration interface assembly.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS210MACCH2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.24 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e14.8 cm x 10.3 cm x 3.2 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eIndustrial rated range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eSystem-bus dependent\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS210MACCH2A integrates into the Mark VI control platform to facilitate deterministic communication between field instrumentation and the controller backplane. The module utilizes defined backplane bus communication velocity to manage signal throughput, ensuring that I\/O scan timing adheres to system requirements. Firmware flash compatibility is dictated by the specific Mark VI rack controller revision, which oversees hardware synchronization. The unit supports I\/O density scaling by providing a stable interface for field wiring, allowing for modular expansion of control loops while maintaining the deterministic performance required for automated drive assemblies.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is the IS210MACCH2A board hot-swappable in an energized rack?\u003c\/p\u003e\n\u003cp\u003eA: No. Any insertion or removal of the module must be performed with the power removed from the control rack to prevent backplane pin damage or corruption of the active control state.\u003c\/p\u003e\n\u003cp\u003eQ: Are there specific firmware version requirements for this board?\u003c\/p\u003e\n\u003cp\u003eA: Yes. Firmware compatibility is version-dependent based on the Mark VI system revision. Consult the site-specific system manual to ensure the controller firmware aligns with the hardware revision of the module.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Secure the board in the chassis using the standard mounting hardware. Ensure the board is aligned properly with the backplane connector to avoid mechanical stress on the PCB.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring:\u003c\/strong\u003e Terminate field wiring at the designated terminal points. Ensure that all shields for analog or communication signal lines are grounded at the system's common reference point to mitigate noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection:\u003c\/strong\u003e Before powering the rack, perform a visual inspection for any debris or oxidation on the connectors. Verify that all terminal connections are tight and meet electrical specifications.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnvironment:\u003c\/strong\u003e Operate the board within a clean and temperature-controlled environment. Dust buildup or excessive moisture may degrade the conformal coating and lead to signal instability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVerification:\u003c\/strong\u003e Upon initial power-up, use the diagnostic console to verify that the board is correctly mapped to the expected I\/O addresses in the Mark VI controller configuration.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52937966780725,"sku":"IS210MACCH2A","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/IS210MACCH2AFG_6bad453c-0f0f-4d50-9f4e-643c043b4d53.png?v=1780041326","url":"https:\/\/www.5gplc.com\/products\/ge-is210macch2a-printed-circuit-board","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}