{"product_id":"ge-is200tbcis2c-discrete-input-terminal-board","title":"GE IS200TBCIS2C Discrete Input Terminal Board","description":"\u003cp\u003eConfigured for discrete signal termination in Mark VIeS control platforms, the \u003cstrong\u003eGE IS200TBCIS2C\u003c\/strong\u003e (\u003cstrong\u003eIS200TBCIS2C\u003c\/strong\u003e Terminal Board) provides direct physical\/electrical execution.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200TBCIS2C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive (Signal distribution)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTerminals\u003c\/td\u003e\n\u003ctd\u003e2 x 24-point terminal blocks (TB1, TB2)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control and Drives Characteristics\u003c\/h3\u003e\n\u003cp\u003eThe IS200TBCIS2C serves as a physical interface layer within the Mark VIeS architecture, facilitating the transition from field wiring to backplane bus communication. Deterministic network performance within the Mark VIeS system relies on the integrity of these terminal-to-controller signal paths. Maintaining low-latency connectivity requires that field wiring connections remain secure and free from oxidation. The design includes parallel component rows to manage discrete input signal conditioning, ensuring compatibility with standard firmware flash programming and I\/O module scanning sequences utilized in the Mark VIeS ecosystem.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Are the TB1 and TB2 terminal blocks interchangeable for field wiring?\u003c\/p\u003e\n\u003cp\u003eA: No. TB1 and TB2 are designated for specific input channels. Consult the system-specific wiring diagrams to ensure field conductors are landed on the correct terminals to match the I\/O module configuration.\u003c\/p\u003e\n\u003cp\u003eQ: Can this terminal board be replaced while the I\/O module is powered?\u003c\/p\u003e\n\u003cp\u003eA: The board functions as a passive termination point. While physical replacement is possible, any disconnection of field wiring will trigger an open-circuit fault in the corresponding controller input channel. De-energize the associated loop prior to removing or installing field wiring.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTerminal Tightening:\u003c\/strong\u003e Use an appropriately sized screwdriver to tighten terminal screws. Ensure wire ferrules are used if applicable to prevent strand damage and maintain high-pressure contact.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShielding:\u003c\/strong\u003e Terminate cable shields at the designated ground lugs on the chassis to minimize electromagnetic interference. Avoid routing signal wiring alongside high-voltage power cables to maintain signal fidelity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMechanical Stability:\u003c\/strong\u003e Ensure the board is firmly seated on the DIN rail or mounting standoffs. Verify that all fasteners are torqued to prevent board vibration, which can lead to intermittent contact in high-vibration environments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLabeling:\u003c\/strong\u003e Utilize the factory-provided white markings on the terminal blocks for verification against system point-to-point diagrams during loop checks.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52988239937845,"sku":"IS200TBCIS2C","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/IS200TBCIS2CCD_ebac6b87-e40d-4541-aff2-dccd589689bb.jpg?v=1781149329","url":"https:\/\/www.5gplc.com\/products\/ge-is200tbcis2c-discrete-input-terminal-board","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}