{"product_id":"ge-is200eacfg1b-ac-feedback-board","title":"GE IS200EACFG1B AC Feedback Board","description":"\u003cp\u003eConfigured for exciter supply monitoring in EX2100 Excitation Control platforms, the \u003cstrong\u003eGE IS200EACFG1B\u003c\/strong\u003e (\u003cstrong\u003eIS200EACFG1B\u003c\/strong\u003e AC Feedback Board) provides direct physical\/electrical execution of AC voltage and current measurement.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200EACFG1B\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMeasurement Inputs\u003c\/td\u003e\n\u003ctd\u003eExciter PPT AC supply voltage and current\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication Velocity and Firmware Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe IS200EACFG1B functions as a signal acquisition interface within the EX2100 control architecture. It samples phase voltage outputs derived from potential transformers and maps them to internal system registers. Deterministic communication via the backplane bus ensures that the voltage feedback data is processed in phase with control loop requirements. Firmware flash compatibility is managed through the master controller, allowing for calibration adjustments of the voltage measurement scaling to account for varying potential transformer ratios within the exciter system.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: How are the potential transformer (PT) voltage inputs verified on the board?\u003c\/p\u003e\n\u003cp\u003eA: Verification is performed via voltage test rings TP1 through TP4. Phase-to-phase voltage AB is measured between TP1 and TP2, BC between TP3 and TP4, and CA between TP4 and TP1. Ensure high-impedance measurement instrumentation is utilized to avoid loading the PT secondary circuits.\u003c\/p\u003e\n\u003cp\u003eQ: Can this board be replaced without recalibrating the excitation control loops?\u003c\/p\u003e\n\u003cp\u003eA: Given that the board serves as an analog feedback interface, any physical replacement requires verification of the voltage feedback scaling within the EX2100 configuration software to ensure measured values correlate with actual primary side inputs.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003ePre-Installation Inspection\u003c\/strong\u003e: Inspect the board for physical damage to the test rings and edge connectors. Ensure that the PCB surface is free of conductive dust or contaminants that could cause flashover at the PT input voltages.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSignal Wiring\u003c\/strong\u003e: PT secondary wiring must be routed to avoid proximity to high-current output cables. Maintain consistent phase orientation during termination at the board inputs to prevent phase-shift errors in the feedback logic.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding\u003c\/strong\u003e: The PCB must be securely seated in the designated EX2100 rack slot to ensure proper connection to the chassis ground plane. This is required for the stability of the analog-to-digital measurement reference.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaintenance\u003c\/strong\u003e: Periodically check for tightness of terminal connections to prevent high-resistance contact points, which can introduce thermal noise and degrade the signal-to-noise ratio of the AC feedback measurements.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52949098692917,"sku":"IS200EACFG1B","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/IS200EACFG1B.png?v=1780300958","url":"https:\/\/www.5gplc.com\/products\/ge-is200eacfg1b-ac-feedback-board","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}