{"product_id":"ge-ds200sdccg4a-drive-control-board","title":"GE DS200SDCCG4A Drive Control Board","description":"\u003cp\u003eConfigured for high-speed motor and drive regulation in Mark V control systems, the \u003cstrong\u003eGE DS200SDCCG4A\u003c\/strong\u003e (\u003cstrong\u003eDS200SDCCG4A\u003c\/strong\u003e Controller Board) provides direct physical execution of drive control, motor control, and co-motion processing tasks.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200SDCCG4A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE (General Electric)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eStandard industrial range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMicroprocessors\u003c\/td\u003e\n\u003ctd\u003e80C186 (DCP), 80C196 (MCP), TMS320C25 (CMP)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMemory\u003c\/td\u003e\n\u003ctd\u003e4 x EPROM, 1 x EEPROM\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication and Deterministic Processing\u003c\/h3\u003e\n\u003cp\u003eThe DS200SDCCG4A utilizes three distinct 16-bit microprocessors interconnected via dual-ported RAM (DPR) to ensure deterministic communication across the Mark V backplane. The Drive Control Processor (DCP) handles system-level operations, while the Motor Control Processor (MCP) manages inner-loop current regulation. For computationally intensive tasks, the Co-motion Processor (CMP) employs a TMS320C25 digital signal processor. Firmware flash compatibility is managed through onboard EPROM sockets, with site-specific calibration parameters stored within the U9 EEPROM. Precise address decoding and DMA control are maintained to ensure stable backplane bus communication velocity during complex ac\/dc motor drive sequences.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Are the memory chips (EPROM\/EEPROM) hot-swappable during system operation?\u003c\/p\u003e\n\u003cp\u003eA: No. Memory chips located in the sockets must be replaced only while the card is powered down. Hot-swapping these components while the drive is active will cause immediate control failure and potential corruption of configuration data.\u003c\/p\u003e\n\u003cp\u003eQ: How is the CMP processor utilized within the SDCC architecture?\u003c\/p\u003e\n\u003cp\u003eA: The CMP (U35) is enabled only for motor control algorithms requiring processing power exceeding the capabilities of the MCP. It interfaces exclusively with its dedicated dual-ported RAM and EPROM to maintain high-speed execution of math-intensive control loops.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eEnsure the control system is fully de-energized before inserting or removing the DS200SDCCG4A card from the Mark V cabinet rack.\u003c\/li\u003e\n\u003cli\u003eVerify that all jumper settings on the replacement board match the original configuration before installation to prevent conflicts in I\/O scaling.\u003c\/li\u003e\n\u003cli\u003eHandle the board by the edges or the faceplate to avoid electrostatic discharge (ESD) damage to the microprocessors and memory chips.\u003c\/li\u003e\n\u003cli\u003eAfter installation, confirm that the EEPROM (U9) contains the correct site-specific parameters, as the new board will not be pre-configured with the specific tuning constants of the drive it is replacing.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":53038928920885,"sku":"DS200SDCCG4A","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/DS200SDCCG4AGD_539309cc-db4a-4929-80bf-afe9c3ef7a8a.png?v=1782456152","url":"https:\/\/www.5gplc.com\/products\/ge-ds200sdccg4a-drive-control-board","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}