{"product_id":"ge-ds200lppag1a-line-protection-card","title":"GE DS200LPPAG1A Line Protection Card","description":"\u003cp\u003eConfigured for power line monitoring and fault isolation in EX2000 excitation control systems, the \u003cstrong\u003eGE DS200LPPAG1A\u003c\/strong\u003e (\u003cstrong\u003eDS200LPPA\u003c\/strong\u003e Line Protection Card) provides direct physical execution of transmission line analysis and abnormal condition detection.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200LPPAG1A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e2 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 deg C to +65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e+18 VDC to +32 VDC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterfaces\u003c\/td\u003e\n\u003ctd\u003e2 terminal blocks (3 terminals each), 7 jumpers (JP1-JP7)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control and Firmware Flash Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe DS200LPPAG1A is integrated into the EX2000 system to monitor transmission line parameters, including voltage stability, overcurrent, and short-circuit conditions. Deterministic fault detection is achieved through continuous analog signal monitoring. When abnormal conditions such as line-to-ground faults or overloads are identified, the card triggers an isolation sequence, sending signals to disconnect the affected line to protect the generator and associated turbine equipment. The module supports firmware flash compatibility through the QNX Neutrino operating system environment, ensuring the protection logic remains aligned with system control requirements. I\/O density scaling and fault-detection sensitivity are calibrated using seven onboard jumpers (JP1-JP7), which define the protection parameters and isolation behavior.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the JP1 through JP7 jumpers be adjusted during turbine operation?\u003c\/p\u003e\n\u003cp\u003eA: No. Any changes to jumper configurations to alter protection thresholds or isolation behavior must be performed while the system is de-energized and the turbine is offline to prevent unexpected signal states or system trips.\u003c\/p\u003e\n\u003cp\u003eQ: How does the DS200LPPAG1A interface with the QNX Neutrino operating system?\u003c\/p\u003e\n\u003cp\u003eA: The card provides digitized fault status signals that are interpreted by the QNX Neutrino-based control platform. This allows for real-time monitoring and logging of line faults detected by the hardware.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eEnsure the EX2000 control cabinet is de-energized and all power sources are isolated before installing or removing the module to avoid electrical shock.\u003c\/li\u003e\n\u003cli\u003eVerify that the input power supply is within the +18 VDC to +32 VDC range before initiating system startup.\u003c\/li\u003e\n\u003cli\u003eTerminate signal wires into the two onboard 3-terminal blocks, ensuring connections are tightened to industrial torque standards to prevent high-resistance contact faults.\u003c\/li\u003e\n\u003cli\u003ePerform a dry-run diagnostic test after installation to ensure the protection card correctly communicates fault status signals to the control platform before placing the turbine into operation.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":53039092891957,"sku":"DS200LPPAG1A","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/DS200LPPAG1AAA_34b9bf31-4677-4006-9be9-3a0adc1bddb6.png?v=1782459419","url":"https:\/\/www.5gplc.com\/products\/ge-ds200lppag1a-line-protection-card","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}