{"product_id":"ds200rtbag3ahc-general-electric-relay-terminal-board","title":"DS200RTBAG3AHC | General Electric | Relay Terminal Board","description":"\u003cp\u003eThe \u003cstrong\u003eGE DS200RTBAG3AHC\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eDS200RTBA\u003c\/strong\u003e Relay Terminal Card, operates as a dedicated hardware component for contact-based signal distribution and drive excitation control within EX2000 systems.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200RTBAG3AHC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCore Components\u003c\/td\u003e\n\u003ctd\u003e10 relays (K20-K29), 52 terminal points\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control \u0026amp; Firmware Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe DS200RTBAG3AHC utilizes a hard-wired relay matrix to execute discrete logic switching. Deterministic control is maintained via local pilot relay activation or remote logic inputs, ensuring synchronized response across the I\/O bus. The board supports high-density I\/O scaling through its 52 terminal points, which provide configurable Normally Open (NO) and Normally Closed (NC) contact states. Firmware flash compatibility is not applicable to this terminal board, as all signal logic is implemented via physical electromechanical contact configurations (DPDT for K20-K26, 4PDT for K27-K29). Backplane power distribution is managed through dedicated CPH (positive) and CPN (negative) stab connectors, which supply potential to pluggable circuits C1PL-C5PL and Y9PL-Y37PL.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Are the relays K20-K26 and K27-K29 interchangeable?\u003c\/p\u003e\n\u003cp\u003eA: No. The relay types utilize distinct contact configurations and current ratings. K20-K26 are DPDT 10 A units, while K27-K29 are 4PDT 1 A units. Replacement must match the specific part number requirements for each relay location to maintain circuit integrity.\u003c\/p\u003e\n\u003cp\u003eQ: How is control power applied to the pluggable circuits?\u003c\/p\u003e\n\u003cp\u003eA: Control power is introduced via the CPH and CPN stab connectors. CPH functions as the positive terminal and CPN as the negative. Ensure these connections are secure before energizing the pluggable circuit paths C1PL-C5PL or Y9PL-Y37PL to avoid arcing or intermittent contact.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTerminal Identification\u003c\/strong\u003e: Verify all 52 signal wires against the cabinet wiring schematic before landing. Ensure that the K20 Form C contact series is correctly mapped to the intended Normally Open or Normally Closed positions.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTorque Requirements\u003c\/strong\u003e: Tighten terminal block screws to manufacturer-recommended torque values to prevent high-resistance connections, which can lead to overheating during sustained relay operation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Seating\u003c\/strong\u003e: Ensure the CPH and CPN stab connectors are fully engaged. Loose stab connections in high-vibration excitation environments can result in intermittent control power loss.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnvironmental Limits\u003c\/strong\u003e: Maintain the cabinet internal temperature between 0 and 60 deg C. Exceeding these limits can affect the coil pick-up voltages and reduce the operational lifespan of the electromechanical relays.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52991849234741,"sku":"DS200RTBAG3AHC","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/DS200RTBAG3AHC1.png?v=1781251201","url":"https:\/\/www.5gplc.com\/products\/ds200rtbag3ahc-general-electric-relay-terminal-board","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}