{"product_id":"ds200dtbcg1aaa-general-electric-contact-output-termination-module","title":"DS200DTBCG1AAA | General Electric | Contact Output Termination Module","description":"\u003cp\u003eThe \u003cstrong\u003eGE DS200DTBCG1AAA\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eDS200DTBCG1\u003c\/strong\u003e Contact Output Termination Module, operates as a dedicated hardware component for relay signal distribution and contact output termination within Mark V turbine control systems.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200DTBCG1AAA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCore Components\u003c\/td\u003e\n\u003ctd\u003e2 terminal blocks (110 pins each), 10 jumpers\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control \u0026amp; Firmware Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe DS200DTBCG1AAA serves as a passive interface for relay signaling, facilitating connection between the Mark V turbine control backplane and field-level devices. The module manages I\/O density scaling by providing high-density termination points (220 total signal terminations). Deterministic signal propagation is maintained through direct path wiring to designated interface boards, including TCRA (JS1-JS8) and TCPD (J8) units. As a terminal board, the module does not utilize firmware; therefore, firmware flash compatibility is not applicable. System performance relies on the integrity of the physical contact points and the correct configuration of the onboard jumpers to match the specific drive application requirements.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can this module be hot-swapped while the system is energized?\u003c\/p\u003e\n\u003cp\u003eA: No. All power sources supplying the drive, including AC and DC feeds, must be disconnected before module replacement. The board handles high-voltage contact outputs (125 V DC), presenting an electrical hazard if handled while energized.\u003c\/p\u003e\n\u003cp\u003eQ: What is the function of the 10 onboard jumpers?\u003c\/p\u003e\n\u003cp\u003eA: The jumpers are configured to route specific relay signals and power references across the board. They must be set in accordance with the specific turbine control cabinet wiring diagram to ensure proper signal mapping between the interface connectors (JS1-JS8) and the external field wiring.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower Isolation\u003c\/strong\u003e: Verify that all power sources to the drive cabinet are isolated. This includes disabling rectifiers (e.g., via fuse removal) and opening upstream circuit breakers to ensure a zero-energy state.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring Documentation\u003c\/strong\u003e: Prior to removing the existing module, label all 110-pin terminal block connections. Given the high density of terminations, improper reconnection of field wires can result in logic errors or damage to connected relay coils.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMechanical Retention\u003c\/strong\u003e: Ensure the board is firmly secured to the cabinet mounting surface. Tighten all terminal block screws to the specified torque to prevent loose connections, which can cause signal intermittency or resistive heating.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShielding and Grounding\u003c\/strong\u003e: Maintain appropriate separation between low-voltage signal wiring and high-voltage power lines within the cabinet. Ensure the board chassis is properly referenced to the cabinet ground to minimize electromagnetic interference on the contact output paths.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":52991844647221,"sku":"DS200DTBCG1AAA","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/DS200DTBCG1AAA.png?v=1781250578","url":"https:\/\/www.5gplc.com\/products\/ds200dtbcg1aaa-general-electric-contact-output-termination-module","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}