{"product_id":"con021-pr6423-010-040-cn-emerson-eddy-current-sensor-system","title":"CON021+PR6423\/010-040-CN Emerson Eddy Current Sensor System","description":"\u003cp\u003eThe \u003cstrong\u003eEmerson CON021+PR6423\/010-040-CN\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eCON021+PR6423\u003c\/strong\u003e Proximity Sensor System, operates as a dedicated hardware component for non-contact shaft displacement and vibration measurement within MMS 6000 and Ovation machinery protection platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eCON021+PR6423\/010-040-CN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eEmerson\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA \/ Germany\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eConverter: 0.2 kg; Sensor assembly: approx. 0.18 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eConverter: 4.4 cm x 10.2 cm x 10.8 cm; Sensor tip diameter: 8 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eSensor Tip: -35 to +200 deg C; Cable \u0026amp; Connector: -35 to +150 deg C; ISF Temperature Range: 0 to +45 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePowered via monitoring rack backplane \/ loop supply\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMeasuring Range\u003c\/td\u003e\n\u003ctd\u003e2.0 mm (80 mils) nominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInitial Air Gap\u003c\/td\u003e\n\u003ctd\u003e0.5 mm (20 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n\u003ctd\u003e8 V\/mm (203.2 mV\/mil) +\/- 5%\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDeviation from Straight Line (DSL)\u003c\/td\u003e\n\u003ctd\u003e+\/- 0.025 mm (+\/- 1 mil)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTarget Material\u003c\/td\u003e\n\u003ctd\u003e42CrMo4 (AISI\/SAE 4140) standard ferromagnetic steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum Shaft Diameter\u003c\/td\u003e\n\u003ctd\u003e25 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable Option (010-040)\u003c\/td\u003e\n\u003ctd\u003e1.0 m integral cable length with flexible armored conduit sleeve\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEnclosure Protection\u003c\/td\u003e\n\u003ctd\u003eIP66 (IEC 60529); PEEK sensor tip\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003e4-20 mA HART Loop Protocol and Channel Isolation\u003c\/h3\u003e\n\u003cp\u003eThe CON021 signal converter demodulates the high-frequency electromagnetic field produced by the PR6423 probe tip, outputting a precise analog voltage signal (-2 VDC to -18 VDC linear operating range). The module is built with high channel-to-channel isolation and input filtering, preventing cross-talk and ground loop interference when interfacing with 4-20 mA HART transmitters, DCS I\/O racks, or TSI monitoring nodes operating in high-EMI power generation environments.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: What physical protection does the \/010-040 suffix denote compared to standard probe options?\u003c\/p\u003e\n\u003cp\u003eA: The \/010-040 suffix specifies a 1.0-meter integral PTFE lead encased in a flexible armored conduit sleeve, providing mechanical protection against impact, abrasion, and hot debris in turbine housings.\u003c\/p\u003e\n\u003cp\u003eQ: How is the initial gap voltage calibrated during field installation?\u003c\/p\u003e\n\u003cp\u003eA: Mechanically set the probe position to an initial physical air gap of approximately 0.5 mm, then verify that the CON021 analog voltage output reads within the linear midpoint (typically -10 VDC gap voltage) before tightening locknuts.\u003c\/p\u003e\n\u003cp\u003eQ: Can the integral probe cable be cut or spliced to fit spatial constraints?\u003c\/p\u003e\n\u003cp\u003eA: No, the total cable length (integral lead plus extension cable) forms an engineered impedance loop tuned to the CON021 driver oscillator; cutting or trimming cable changes system calibration and introduces measuring errors.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eMount the threaded stainless steel PR6423 sensor body into the bearing housing, ensuring rigid mechanical alignment to eliminate parasitic vibration.\u003c\/li\u003e\n\u003cli\u003eAdjust probe insertion depth to achieve a static 0.5 mm air gap or an approximate -10 VDC output from the CON021 converter.\u003c\/li\u003e\n\u003cli\u003eRoute the armored conduit cable along structural framework, avoiding sharp bend angles that exceed the specified minimum bend radius.\u003c\/li\u003e\n\u003cli\u003eMount the CON021 converter module onto an aluminum DIN rail inside a low-vibration junction enclosure.\u003c\/li\u003e\n\u003cli\u003eConnect probe leads to the CON021 terminals, anchoring cable shield drain wires to a central, low-impedance earth grounding point to prevent noise coupling.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"EMERSON","offers":[{"title":"Default Title","offer_id":53332736213301,"sku":"CON021+PR6423\/010-040-CN","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/CON021_PR6424000-030_e5f048e2-00fa-4c6e-ac4f-9a071ac3d35e.png?v=1787127047","url":"https:\/\/www.5gplc.com\/products\/con021-pr6423-010-040-cn-emerson-eddy-current-sensor-system","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}