{"product_id":"con020-91-signal-conditioner-module-driver-epro","title":"CON020\/91 Signal Conditioner Module Driver | Epro","description":"\u003cp\u003eConfigured for signal conversion in rotating machinery monitoring networks, the \u003cstrong\u003eEpro CON020\/91\u003c\/strong\u003e (\u003cstrong\u003eCON020\/91\u003c\/strong\u003e Signal Conditioner Module Driver) provides direct physical electrical execution for processing transducer inputs into standardized analog signals. The module accepts raw probe inputs and delivers either analog voltage or 4-20 mA current outputs, interfacing directly with TSI monitoring platforms to support continuous data acquisition in machinery protection applications.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eCON020\/91\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eEpro\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e100 mm x 22 mm x 120 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-35 to 85 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput Type\u003c\/td\u003e\n\u003ctd\u003eTransducer Signal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Type\u003c\/td\u003e\n\u003ctd\u003eAnalog Voltage or 4-20 mA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eMechanical Monitoring and TSI Characteristics\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eCON020\/91\u003c\/strong\u003e module is engineered to manage critical signal parameters for eddy-current probe scaling within machinery protection systems. It supports the precise adjustment of gain and offset required for gap voltage validation against -10 VDC targets, ensuring that the sensor response remains linear across the transducer's measurement range. To preserve data integrity in high-density rack configurations, the module incorporates internal cross-talk suppression and EMI immunity filters, which are required for reliable rotor dynamics analysis under varying load and speed conditions.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions (FAQ)\u003c\/h3\u003e\n\u003cp\u003eQ: Can the CON020\/91 be hot-swapped while the machinery is operating?\u003c\/p\u003e\n\u003cp\u003eA: Module removal or replacement during active operation depends on the backplane architecture and system configuration. Ensure the I\/O channel is inhibited in the monitoring software to prevent a false trip or alarm signal before extracting the module.\u003c\/p\u003e\n\u003cp\u003eQ: Is the 4-20 mA output isolated from the power supply ground?\u003c\/p\u003e\n\u003cp\u003eA: The module is designed for industrial integration where loop isolation is required. Consult the system interconnection diagram to confirm if the output stage requires an external isolator to prevent ground loops between the module and the destination input card.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eMount the module on a standard DIN rail or designated rack chassis, ensuring the mechanical locking clip is fully engaged.\u003c\/li\u003e\n\u003cli\u003eTerminate signal input cabling using shielded, twisted-pair wire to minimize electromagnetic interference (EMI) ingress.\u003c\/li\u003e\n\u003cli\u003eVerify that the shield drain wire is bonded to the cabinet earth ground at the rack entry point only to avoid ground loops.\u003c\/li\u003e\n\u003cli\u003eSet the internal jumpers or configuration switches to match the desired output mode (voltage or current) before applying 24 VDC power.\u003c\/li\u003e\n\u003cli\u003eConfirm stable signal output at the terminal block using a calibrated multimeter prior to validating the sensor gap voltage at the probe tip.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"EMERSON","offers":[{"title":"Default Title","offer_id":52956561965365,"sku":"CON020\/91","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/PR6426010-140_CON011916-1202_cef4093b-0e21-4f7e-a15b-7584f7f90f0f.png?v=1780469600","url":"https:\/\/www.5gplc.com\/products\/con020-91-signal-conditioner-module-driver-epro","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}