{"product_id":"abb-ufc721be101-3bhe021889r0101-adcvi-board","title":"ABB UFC721BE101 3BHE021889R0101 ADCVI-BOARD","description":"\u003cp\u003eConfigured for analog-to-digital signal conversion in control platforms, the \u003cstrong\u003eABB UFC721BE101\u003c\/strong\u003e (\u003cstrong\u003e3BHE021889R0101\u003c\/strong\u003e ADCVI-BOARD) provides direct physical signal processing for feedback loop execution.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eUFC721BE101\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eABB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePart Number\u003c\/td\u003e\n\u003ctd\u003e3BHE021889R0101\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eSweden\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.2 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e279 mm x 29 mm x 483 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eStandard industrial ambient\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eSystem backplane dependent\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP deterministic networks\u003c\/h3\u003e\n\u003cp\u003eThe UFC721BE101 operates as a high-speed data acquisition interface, managing backplane bus communication velocity to maintain deterministic synchronization with the controller CPU. The module executes I\/O density scaling to handle high-resolution analog inputs, ensuring that signal conversion latencies remain within system-defined tolerances. Firmware flash compatibility is strictly dependent on the host control unit's revision; firmware updates must be performed via the engineering console to align with the specific hardware ID of the board. The module architecture facilitates transparent communication across the backplane, supporting real-time data streaming required for precise loop control.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the UFC721BE101 support hot-swapping within an active rack?\u003c\/p\u003e\n\u003cp\u003eA: No. Hot-swapping is not permitted. Power must be removed from the backplane prior to module extraction or insertion to prevent electrical transients from damaging the communication bus pins or internal conversion logic.\u003c\/p\u003e\n\u003cp\u003eQ: How is the module synchronized with the master control loop?\u003c\/p\u003e\n\u003cp\u003eA: Synchronization is achieved through the backplane bus timing signals managed by the primary controller. Proper module slot assignment in the system configuration is required to establish the correct interrupt priority and data exchange cycle.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting\u003c\/strong\u003e: Align the board with the rack's guide rails and insert until the connector is fully seated. Tighten the front panel fasteners to ensure mechanical stability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding\u003c\/strong\u003e: Establish a low-impedance connection from the module chassis to the cabinet earth ground. This path is mandatory for EMI suppression and the protection of sensitive analog signal paths.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSignal Shielding\u003c\/strong\u003e: Use shielded twisted-pair cabling for all analog inputs. Connect the shields to the designated cabinet ground terminals to minimize inductive noise coupling from high-voltage AC lines.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThermal Management\u003c\/strong\u003e: Ensure that airflow around the module is not obstructed. Adequate ventilation is necessary to maintain the board's operational accuracy and component lifespan.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection\u003c\/strong\u003e: Before integration, inspect the backplane connector pins for evidence of corrosion or mechanical deformation. Verify that the module enclosure is free of conductive dust or foreign objects.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"ABB","offers":[{"title":"Default Title","offer_id":52965623824693,"sku":"UFC721BE101 3BHE021889R0101","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/UFC721BE1013BHE021889R0101.png?v=1780649375","url":"https:\/\/www.5gplc.com\/products\/abb-ufc721be101-3bhe021889r0101-adcvi-board","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}