{"product_id":"abb-uf-c719-ae01-3bhb003041r0101-i-o-interface-module","title":"ABB UF C719 AE01 3BHB003041R0101 I\/O Interface Module","description":"\u003cp\u003eConfigured for signal conversion and interface management in distributed control networks, the \u003cstrong\u003eABB 3BHB003041R0101\u003c\/strong\u003e (\u003cstrong\u003eUF C719 AE01\u003c\/strong\u003e I\/O Interface) provides direct electrical execution of data acquisition tasks.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eUF C719 AE01\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eABB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eSwitzerland\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.18 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e45.3 cm x 12.8 cm x 4.8 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 deg C to 50 deg C (standard industrial range)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e\u0026lt; 15 W typical\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface Type\u003c\/td\u003e\n\u003ctd\u003eIOEC I\/O Interface\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication Velocity\u003c\/h3\u003e\n\u003cp\u003eThe UF C719 AE01 module facilitates high-speed data exchange across the local backplane bus, supporting deterministic cycle times required for process synchronization. The interface architecture is optimized to minimize bus latency during high-density I\/O polling, ensuring that process signals are updated within the defined scan window of the master controller. Communication velocity is managed by onboard logic that filters bus traffic to maintain integrity during peak load scenarios, preventing buffer overflows in complex control configurations.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions (FAQ)\u003c\/h3\u003e\n\u003cp\u003eQ: Does this module support hot-swapping while the system backplane is energized?\u003c\/p\u003e\n\u003cp\u003eA: No. Power to the rack must be disconnected before attempting to seat or remove the module to prevent electrical damage to the backplane pins and the I\/O interface circuitry.\u003c\/p\u003e\n\u003cp\u003eQ: How is the communication address defined for this module?\u003c\/p\u003e\n\u003cp\u003eA: The module address is typically assigned via the hardware configuration software or via physical backplane slot indexing, depending on the specific backplane controller firmware revision.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Secure the module within the designated rack slot using the provided mechanical retention screws to ensure a positive connection to the backplane.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding:\u003c\/strong\u003e Verify that the system rack chassis is connected to a low-impedance earth ground to provide proper shielding for the internal interface electronics.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring:\u003c\/strong\u003e Use shielded cabling for all I\/O terminations. Ensure the cable shield is grounded at the entry point of the cabinet to prevent high-frequency noise from entering the module through the signal lines.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnvironmental:\u003c\/strong\u003e Ensure the cabinet maintains adequate airflow. Do not obstruct the module ventilation vents, as this can degrade internal components over long-term operation.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"ABB","offers":[{"title":"Default Title","offer_id":52965705482549,"sku":"UF C719 AE01 3BHB003041R0101","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/UFC719AE013BHB003041R0101.png?v=1780652871","url":"https:\/\/www.5gplc.com\/products\/abb-uf-c719-ae01-3bhb003041r0101-i-o-interface-module","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}