{"product_id":"621-9938-serial-i-o-module-honeywell","title":"621-9938 Serial I\/O Module | Honeywell","description":"\u003cp\u003eConfigured for multi-channel serial data management in control system architectures, the \u003cstrong\u003eHoneywell 621-9938\u003c\/strong\u003e (\u003cstrong\u003e621-9938\u003c\/strong\u003e Serial I\/O Module) provides direct physical and electrical execution of bi-directional data exchange between the PLC and remote peripheral devices. The module serves as the primary dual-port interface utilized to execute serial I\/O signal routing across Honeywell PLC platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e621-9938\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eHoneywell\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.70 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePort Configuration\u003c\/td\u003e\n\u003ctd\u003eDual Port\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStatus Indicators\u003c\/td\u003e\n\u003ctd\u003eFront-mounted LEDs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eDCS Process Control and Connectivity\u003c\/h3\u003e\n\u003cp\u003eThe 621-9938 module enables dual-stream serial communication, providing independent I\/O paths for peripheral data integration. Each port supports channel-to-channel isolation, which is required to mitigate common-mode noise and prevent ground-loop interference between the controller backplane and field-side instruments. The module architecture incorporates high-speed transceiver logic designed to maintain data integrity during peak bus traffic, supporting consistent communication latency required for deterministic control loops. Integrated cold junction compensation (CJC) is offloaded to localized sensor interface cards, allowing this module to concentrate on high-throughput serial framing and synchronization for 4-20 mA HART loop protocol data encapsulation where applicable within the broader control environment.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does this module support hot-swapping within the controller rack?\u003c\/p\u003e\n\u003cp\u003eA: No. The 621-9938 is not designed for hot-swapping. Insertion or removal of the module while the backplane is powered will likely result in a system-wide bus fault and may cause physical damage to the serial transceiver pins.\u003c\/p\u003e\n\u003cp\u003eQ: How are the dual ports configured for communication settings?\u003c\/p\u003e\n\u003cp\u003eA: Port parameters such as baud rate, parity, and stop bits are generally managed via the PLC programming software or module configuration register mapping. Ensure that the field device settings strictly match the software configuration to avoid data framing errors.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eVerify that the controller rack is fully de-energized before beginning module installation.\u003c\/li\u003e\n\u003cli\u003eAlign the module with the chassis slot and seat firmly into the backplane connector to ensure stable physical and electrical contact.\u003c\/li\u003e\n\u003cli\u003eSecure the module to the rack frame using the provided mounting fasteners to establish a rigid ground path for EMI suppression.\u003c\/li\u003e\n\u003cli\u003eUtilize shielded, twisted-pair communication cabling for all serial connections, ensuring the shield is terminated to the designated ground terminal to prevent signal corruption.\u003c\/li\u003e\n\u003cli\u003ePerform a diagnostic loop-back test upon system startup to confirm that both serial ports are initialized and communicating with the intended remote devices.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Honeywell","offers":[{"title":"Default Title","offer_id":52976086450485,"sku":"621-9938","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/621-99381.png?v=1780993187","url":"https:\/\/www.5gplc.com\/products\/621-9938-serial-i-o-module-honeywell","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}