{"product_id":"51202329-604-honeywell-tdc-3000-header-cable","title":"51202329-604 | Honeywell | TDC 3000 Header Cable","description":"\u003cp\u003eConfigured for module-to-module signal routing in Honeywell control networks, the \u003cstrong\u003eHoneywell 51202329-604\u003c\/strong\u003e (\u003cstrong\u003e51202329-604\u003c\/strong\u003e Header Cable) provides direct physical\/electrical execution. It establishes fixed header termination paths across system interface boards to maintain low-voltage signal continuity and EMI\/RFI noise rejection across I\/O link channels.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e51202329-604\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eHoneywell\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eFixed Length Header Harness\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive Component (0 W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable Type\u003c\/td\u003e\n\u003ctd\u003eHeader-Terminated I\/O Link Cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShielding\u003c\/td\u003e\n\u003ctd\u003eMulti-Strand EMI\/RFI Shielding\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector Interface\u003c\/td\u003e\n\u003ctd\u003eHoneywell Header-Style I\/O Link Termination\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003e4-20 mA HART Loop Protocol Behavior\u003c\/h3\u003e\n\u003cp\u003eWithin Honeywell DCS environments, header-terminated I\/O link cables carry analog loop signals including 4-20 mA with optional HART modulation. The continuous shielding structure suppresses noise ingress along shared wiring paths, while channel-to-channel isolation within receiving I\/O modules prevents cross-talk when multiple signal loops pass through adjacent header connectors. Impedance consistency across the assembly preserves signal loop scaling and prevents telemetry drift during continuous operation.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the 51202329-604 header cable be disconnected while the control system is energized?\u003c\/p\u003e\n\u003cp\u003eA: The cable is a passive component and suffers no electrical degradation, but disconnecting it while live will interrupt active process loops. Ensure connected I\/O cards are set to a safe state before removal.\u003c\/p\u003e\n\u003cp\u003eQ: Does the 51202329-604 cable introduce power draw onto the backplane bus?\u003c\/p\u003e\n\u003cp\u003eA: No, the cable imposes zero electrical load on the system supply; power consumption is governed entirely by connected active I\/O modules and field devices.\u003c\/p\u003e\n\u003cp\u003eQ: Are specific software configurations or firmware updates required to install this cable assembly?\u003c\/p\u003e\n\u003cp\u003eA: No firmware resides on the cable. Physical compatibility is determined solely by matching header pinouts and standard Honeywell I\/O link wiring specifications.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eEnsure the header connector is fully seated into the board receptacle and latched to resist disconnection under panel vibration.\u003c\/li\u003e\n\u003cli\u003eTerminate the overall cable shield strictly at the control panel ground point to prevent circulatory ground loops.\u003c\/li\u003e\n\u003cli\u003eObserve standard wire bending limits near the header strain relief to protect internal conductors from mechanical fatigue.\u003c\/li\u003e\n\u003cli\u003eRoute the assembly inside grounded wire raceways to maintain isolation from high-voltage AC lines.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Honeywell","offers":[{"title":"Default Title","offer_id":53599242912053,"sku":"51202329-604","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/51202329-102_Cocoai_b5dc72d8-55e6-4413-a674-7de7ffe07a16.png?v=1789612172","url":"https:\/\/www.5gplc.com\/products\/51202329-604-honeywell-tdc-3000-header-cable","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}