{"product_id":"51201420-010-honeywell-field-termination-assembly-cable","title":"51201420-010 Honeywell Field Termination Assembly Cable","description":"\u003cp\u003eThe \u003cstrong\u003eHoneywell 51201420-010\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eMU-KFTA10\u003c\/strong\u003e Field Termination Assembly Cable, operates as a dedicated hardware component for field signal interconnections within Honeywell DCS platforms. It establishes point-to-point electrical continuity between field devices, termination assemblies, and I\/O module assemblies.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e51201420-010\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eHoneywell\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA \/ Global Manufacturing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e10 meters overall length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-20 to 70 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive physical media\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCatalog Number\u003c\/td\u003e\n\u003ctd\u003eMU-KFTA10\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFunctionality\u003c\/td\u003e\n\u003ctd\u003eField Termination Assembly (FTA) interconnect cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSignal Compatibility\u003c\/td\u003e\n\u003ctd\u003eDiscrete and 4-20 mA HART loop signals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eChannel-to-Channel Isolation \u0026amp; Signal Rejection\u003c\/h3\u003e\n\u003cp\u003eIn process control networks and DCS architectures, signal isolation and noise mitigation maintain feedback loop accuracy. The Honeywell 51201420-010 FTA cable assembly utilizes shielded, low-capacitance conductor pairs engineered to prevent electromagnetic interference (EMI) from corrupting analog input\/output loops and digital switching lines. Ground potential equalization across the cable assembly ensures galvanic separation between field wiring terminals and sensitive backplane electronics, preserving 4-20 mA HART signal linearity across the full 10 meters length.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can this cable assembly be hot-swapped while the DCS I\/O module is actively powered?\u003c\/p\u003e\n\u003cp\u003eA: Passive FTA cables may be disconnected from field termination assemblies; however, signal circuits should be de-energized or put in manual loop mode prior to disconnection to prevent process field trips.\u003c\/p\u003e\n\u003cp\u003eQ: How is the cable shielding grounded to avoid ground loops between field devices and the control cabinet?\u003c\/p\u003e\n\u003cp\u003eA: The overall shield braid must be grounded at a single point, typically via the ground lug or chassis termination bar inside the main DCS cabinet enclosure.\u003c\/p\u003e\n\u003cp\u003eQ: Does the cable support digital HART protocol pass-through along with standard 4-20 mA analog signals?\u003c\/p\u003e\n\u003cp\u003eA: Yes, the cable dielectric and conductor geometry maintain frequency response specs required for bidirectional HART digital modulation over the 4-20 mA DC carrier.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRoute the FTA cable through designated low-voltage control wireways, keeping at least 200 mm clearance from high-voltage AC power distribution lines.\u003c\/li\u003e\n\u003cli\u003eSecure strain relief brackets at both the FTA terminal block end and the I\/O rack interface to prevent stress on connector pin contacts.\u003c\/li\u003e\n\u003cli\u003eEnsure the ambient operating temperature along the cable tray path remains within the -20 to 70 deg C rating.\u003c\/li\u003e\n\u003cli\u003eVerify that pin alignments match the keying slots on the Honeywell FTA connectors before applying insertion force.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Honeywell","offers":[{"title":"Default Title","offer_id":53191576518965,"sku":"51201420-010","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/51202905-100_170b3692-87a4-4a02-8954-f24d937ba0d2.png?v=1784615212","url":"https:\/\/www.5gplc.com\/products\/51201420-010-honeywell-field-termination-assembly-cable","provider":"High Five PLC Solution Limited","version":"1.0","type":"link"}