{"product_id":"330103-00-17-10-02-05-bently-nevada-3300-xl-8-mm-proximity-probe","title":"330103-00-17-10-02-05 | Bently Nevada | 3300 XL 8 mm Proximity Probe","description":"\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330103-00-17-10-02-05\u003c\/strong\u003e is an eddy current proximity probe from the 3300 XL 8 mm series for non-contact shaft displacement and vibration measurement. This configuration features an M10 x 1 case thread, a 0 mm unthreaded length (option 00), a 170 mm overall case length (option 17), a 1.0 m (3.3 ft) standard cable with a miniature coaxial ClickLoc connector (option 02), and CSA, ATEX, and IECEx approvals (option 05).\u003c\/p\u003e\n\u003ch3\u003eMeasurement Range and Electrical Characteristics\u003c\/h3\u003e\n\u003cp\u003eThis probe provides a 2 mm (80 mils) linear range spanning 0.25 mm to 2.3 mm (10 to 90 mils), with an output voltage of approximately -1 to -17 VDC across the linear span. For standard radial vibration setups, set the gap to -9 VDC, corresponding to approximately 1.27 mm (50 mils).\u003c\/p\u003e\n\u003cp\u003eAt the 1.0 m probe length, DC resistance is 7.59 ohm +\/- 0.50. Field wiring supports 0.2 to 1.5 mm2 (16-24 AWG) on 3-conductor shielded triad cable, with up to 305 m (1,000 ft) maximum extension cable length between sensor and monitor.\u003c\/p\u003e\n\u003ch3\u003eMechanical Construction and Hazardous Area Ratings\u003c\/h3\u003e\n\u003cp\u003eThe probe combines a polyphenylene sulfide (PPS) tip with an AISI 303 or 304 stainless steel (SST) case, an M10 x 1 thread (15 mm maximum thread engagement), and a Viton O-ring pressure seal that is not pressure tested prior to shipment. Standard temperature rating is -52 deg C to +177 deg C (-62 deg F to +350 deg F), with extended ratings listed for the tip (-52 deg C to +218 deg C) and cable (-51 deg C to +260 deg C), while weight is 323 g\/m (11.4 oz).\u003c\/p\u003e\n\u003cp\u003eAgency approvals (option 05) cover CSA, ATEX, and IECEx across EPL Ga\/Gc, EPL Dc, and Division classifications, with temperature classes T1 through T5 and dust classes defined over specified ambient ranges. Note that low-temperature exposure below -34 deg C risks pressure seal failure.\u003c\/p\u003e\n\u003ch3\u003eInstallation and Wiring Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eUse 3-conductor shielded triad cable with tinned conductors sized from 0.2 to 1.5 mm2 (16-24 AWG) for field wiring.\u003c\/li\u003e\n\u003cli\u003eKeep total field wiring under 305 m (1,000 ft) between sensor and monitor, and check frequency response data for high-frequency rolloff over longer cable runs.\u003c\/li\u003e\n\u003cli\u003eAdjust the probe gap to approximately -9 VDC (about 1.27 mm \/ 50 mils) for standard radial vibration measurement.\u003c\/li\u003e\n\u003cli\u003eDo not expose the probe below -34 deg C if avoiding pressure seal failure is required for the application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e330103-00-17-10-02-05\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSeries \/ Product Type\u003c\/td\u003e\n\u003ctd\u003e3300 XL 8 mm Proximity Probe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLinear Range\u003c\/td\u003e\n\u003ctd\u003e2 mm (80 mils), spanning 0.25 mm to 2.3 mm (10 to 90 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Voltage\u003c\/td\u003e\n\u003ctd\u003eApprox. -1 to -17 VDC over full linear range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRecommended Radial Vibration Gap\u003c\/td\u003e\n\u003ctd\u003e-9 VDC (approx. 1.27 mm \/ 50 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe DC Resistance\u003c\/td\u003e\n\u003ctd\u003e7.59 ohm +\/- 0.50 (at 1.0 m probe length)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eField Wiring\u003c\/td\u003e\n\u003ctd\u003e0.2 to 1.5 mm2 (16-24 AWG), 3-conductor shielded triad cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum Extension Cable Length\u003c\/td\u003e\n\u003ctd\u003e305 m (1,000 ft) between sensor and monitor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCase Thread\u003c\/td\u003e\n\u003ctd\u003eM10 x 1 (15 mm max thread engagement)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eUnthreaded Length\u003c\/td\u003e\n\u003ctd\u003e0 mm (option 00)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOverall Case Length\u003c\/td\u003e\n\u003ctd\u003e170 mm (option 17)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTotal Length\u003c\/td\u003e\n\u003ctd\u003e1.0 m \/ 3.3 ft (option 10)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector and Cable Type\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector with standard cable (option 02)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTip Material\u003c\/td\u003e\n\u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCase Material\u003c\/td\u003e\n\u003ctd\u003eAISI 303 or 304 stainless steel (SST)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePressure Seal\u003c\/td\u003e\n\u003ctd\u003eViton O-ring (not pressure tested before shipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAgency Approvals\u003c\/td\u003e\n\u003ctd\u003eCSA, ATEX, IECEx (option 05)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHazardous Area Ratings\u003c\/td\u003e\n\u003ctd\u003eia (Zone 0, Div 1): AEx\/Ex ia IIC T5...T1 Ga, Class I, II, III; nA, ec (Zone 2, Div 2): AEx\/Ex nA IIC T5...T1 Gc, Class I, Div 2; EPL Ga\/Gc (T1 to T5) and EPL Dc (T280 deg C to T90 deg C) per ambient limits\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStandard Temperature Range\u003c\/td\u003e\n\u003ctd\u003e-52 deg C to +177 deg C (-62 deg F to +350 deg F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eExtended Temperature Range\u003c\/td\u003e\n\u003ctd\u003eTip: -52 deg C to +218 deg C; Cable: -51 deg C to +260 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRelative Humidity Performance\u003c\/td\u003e\n\u003ctd\u003eLess than 3% ASF change at 93% RH (IEC 68-2-3, 56 days)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e323 g\/m (11.4 oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: What gap voltage is recommended for radial vibration monitoring with \u003cstrong\u003e330103-00-17-10-02-05\u003c\/strong\u003e?\u003c\/p\u003e\n\u003cp\u003eA: Set the gap to approximately -9 VDC, which corresponds to about 1.27 mm (50 mils) within the 0.25 mm to 2.3 mm (10 to 90 mils) linear range.\u003c\/p\u003e\n\u003cp\u003eQ: Is the pressure seal on this probe pressure tested prior to shipment, and what low-temperature limit applies?\u003c\/p\u003e\n\u003cp\u003eA: The Viton O-ring pressure seal is not pressure tested before shipment. Avoid exposing the probe below -34 deg C to prevent pressure seal failure, and verify applicable hazardous-area temperature class limits for your installation.\u003c\/p\u003e\n\u003cp\u003eQ: What field wiring size and maximum cable length apply between the sensor and monitor?\u003c\/p\u003e\n\u003cp\u003eA: Field wiring uses 0.2 to 1.5 mm2 (16-24 AWG) 3-conductor shielded triad cable, with a maximum extension length of 305 m (1,000 ft) between sensor and monitor. Longer runs can introduce high-frequency rolloff, so check the frequency response curve for your setup.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":68424501461301,"sku":"330103-00-17-10-02-05","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/330103-00-03-10-02-00_7c69feb3-b117-4ecd-b9e3-9e69bf503817.jpg?v=1795156917","url":"https:\/\/www.5gplc.com\/products\/330103-00-17-10-02-05-bently-nevada-3300-xl-8-mm-proximity-probe","provider":"High Five Auto Solution Limited","version":"1.0","type":"link"}