{"product_id":"330103-00-03-05-12-00-bently-nevada-3300-xl-8-mm-proximity-probe","title":"330103-00-03-05-12-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe","description":"\u003cp\u003eThe \u003cstrong\u003e330103-00-03-05-12-00\u003c\/strong\u003e is a 3300 XL 8 mm proximity probe designed for continuous static shaft position and dynamic vibration monitoring in industrial machinery protection systems. This eddy-current transducer converts physical displacement into a proportional voltage signal, supporting accurate rotor dynamics analysis and mechanical health tracking.\u003c\/p\u003e\n\u003ch3\u003eSuffix Breakdown \u0026amp; Configuration\u003c\/h3\u003e\n\u003cp\u003eThe model number incorporates specific configuration codes defining its physical and mechanical construction. The base designation represents the 3300 XL 8 mm proximity probe platform. The unthreaded length is specified as 0 mm, while the case length is 30 mm to accommodate designated mounting clearances.\u003c\/p\u003e\n\u003cp\u003eThe integral cable length is 0.5 m, terminated with a miniature coaxial ClickLoc connector featuring Proxpact molded protection for fluid-resistant sealing. This variant carries no agency approval option, aligning with standard installation environments.\u003c\/p\u003e\n\u003ch3\u003eEddy-Current Operation \u0026amp; Signal Scaling\u003c\/h3\u003e\n\u003cp\u003eThe probe operates on the eddy-current principle, generating a high-frequency electromagnetic field at the probe tip to measure the gap between the sensor and the observed conductive shaft. It delivers an output sensitivity of 200 mV\/mil across an 80 mil linear measurement range.\u003c\/p\u003e\n\u003cp\u003eDuring setup, gap voltage validation targets a reference of approximately -10 VDC to maintain linear response across the measurement span. Proper calibration scaling prevents signal distortion and cross-talk between adjacent channels in multi-probe monitoring configurations.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e330103-00-03-05-12-00\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProduct Type\u003c\/td\u003e\n\u003ctd\u003e3300 XL 8 mm Proximity Probe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCase Length\u003c\/td\u003e\n\u003ctd\u003e30 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable Length\u003c\/td\u003e\n\u003ctd\u003e0.5 m (1.6 ft)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector Type\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc with Proxpact molded protection\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAgency Approval\u003c\/td\u003e\n\u003ctd\u003eNone\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLinear Range\u003c\/td\u003e\n\u003ctd\u003e80 mils (2 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Sensitivity\u003c\/td\u003e\n\u003ctd\u003e200 mV\/mil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSystem Compatibility\u003c\/td\u003e\n\u003ctd\u003eStandard 3300 XL extension cables and Proximitor sensors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cp\u003eDo not cut or shorten the integral probe cable, as factory trimming is matched to the specific electrical length required for system calibration. Maintain the manufacturer-specified minimum bend radius to preserve coaxial cable geometry and characteristic impedance.\u003c\/p\u003e\n\u003cp\u003eRoute signal cables away from high-frequency power conductors and motor leads to minimize induced electrical noise. Ensure the ClickLoc connector is fully seated and locked before energizing the monitoring system. Avoid mixing 3300 XL components with NSv or legacy probe systems to prevent impedance mismatch and measurement errors.\u003c\/p\u003e\n\u003cp\u003eFrequently Asked Questions\u003c\/p\u003e\n\u003cp\u003eQ: Can the 330103 probe be hot-swapped during operation?\u003c\/p\u003e\n\u003cp\u003eA: No. Probes and connected loops must be disconnected only when the monitoring system is de-energized to preserve calibration integrity and prevent electrical transients.\u003c\/p\u003e\n\u003cp\u003eQ: How does the probe maintain interchangeability with other system components?\u003c\/p\u003e\n\u003cp\u003eA: It is factory-calibrated and fully interchangeable with standard 3300 XL extension cables and Proximitor sensors without requiring bench recalibration.\u003c\/p\u003e\n\u003cp\u003eQ: What is the nominal output sensitivity of this sensor?\u003c\/p\u003e\n\u003cp\u003eA: The probe provides a standard output sensitivity of 200 mV\/mil across its 2 mm linear measurement range.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":68318964973877,"sku":"330103-00-03-05-12-00","price":66.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/7630\/5461\/files\/330103-00-03-10-02-00_b0b2d619-c9d2-4d7c-8c3a-d43e65e0fe3d.jpg?v=1794985978","url":"https:\/\/www.5gplc.com\/products\/330103-00-03-05-12-00-bently-nevada-3300-xl-8-mm-proximity-probe","provider":"High Five Auto Solution Limited","version":"1.0","type":"link"}